Juniper JN0-661 Exam Questions – Latest 2018

Different learning methods of Juniper Service Provider Routing and Switching JN0-661 exam are used in the software to ease the candidates learning of difficult concepts and they are facilitated for learning Juniper Service Provider Routing and Switching JN0-661 exam with the simulated real Certified Juniper JN0-661 exam scenarios so that you can practice in the same situation that you are going to face in the real exam. Juniper Routing and Switching Services JN0-661 exam Practice test software evaluates the performance by using self-assessment and report feature.

♥ VALID JN0-661 Exam Questions 2018 ♥

JN0-661 exam questions, JN0-661 PDF dumps; JN0-661 exam dumps:: https://www.dumpsschool.com/JN0-661-exam-dumps.html (133 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Juniper JN0-661 Dumps Exam Questions and Answers:

Version: 8.0
Question: 21

ISP 1 wants to configure an IPv6 L3VPN over its IPv4-only MPLS network for Customer-A PE1 has been configured as shown in the exhibit; however, IPv6 routers. In this scenario, which two commands are necessary on PE1 to enable IPv6 connectivity between CE1 and CE2? (Choose two.)

A. set protocols bgp group PE2 family inet6 unicast
B. set interfaces ge-1/1/1.0 family mpls
C. set protocols bgp group PE2 family inet6-vpn
D. set protocols mpls ipv6-tunneling

Answer: AD

Question: 22

Router RR is receiving routes from R1, R2. R3. and R4 as shown in the exhibit Which routes will RR advertise to R5? (Choose two.)

A. routes from R4
B. routes from R1
C. routes from R2
D. routes from R3

Answer: A, B

Question: 23

Referring to the exhibit, you have configured an L3VPN that connects Site-1 and Site-2 together, but the BGP routes are being hidden on the PE routers. The topology in this scenario is shown below.
Site-1 > PE-1 > P-1 > P-2 > PE-2 > Site-2
Which two acttions would allow communication Site-1 and Site-2? (Choose two.)

A. Disable CSPF on under MPLS on P-1 and P-2.
B. Configure DGP on P-1 and P-2.
C. Enable RSVP for all interfaces on P-1 and P-2.
D. Enable LDP for all interfaces on all routers.

Answer: C, D

Question: 24

A layer 2 circuit (RFC 4447) is established between two PE routers to provide connectivity between two customer sites. Which two statements related to this deployment are true?

A. Kompella encapsulation is used in the data plane communications.
B. LDP must be used for the control plane communications
C. BGP must be used for the control plane communications.
D. Martini encapsulation is used in the data plane communications.

Answer: B, D

Question: 25

Referring to the exhibit, which router will be the RP?

A. R4 for all groups
B. R1 for group 224.1.1.11 and R4 for all other groups
C. R1 for all groups
D. R4 for group 224.1.1.12 and R1 for all other groups

Answer: A

Question: 26

You must ensure that r1’s IPv4 loopback address exists in r3’s inet 0 routing table
Referring to the exhibit, which statement is true?

A. An IPv4 unicast realm can be enabled on each router.
B. A policy can be configured on M to redistribute 172.16.100.1/32 into OSPFv2, which would cause r3 to eventually learn the route and place it into inet0.
C. A RIB group can be configured on r3 to copy that route into inet 0 because 172.16.100.1/32 exists in r3’s inet6.0 table
D. A policy can be configured on r1 to redistribute 172 16 100 1/32 into OSPFv3, which would cause r3 to eventually learn the route and place it into inet 0.

Answer: C

New Updated JN0-661 Exam Questions JN0-661 PDF dumps JN0-661 practice exam dumps: https://www.dumpsschool.com/JN0-661-exam-dumps.html